Impeller for Volvo Penta D1 Series, D2-40, MD2010-2040, MD1 / 2 / 3B, MD11 / 17 & AQ Series

SVB item number: 27251
Replacement impellers for various engines. ATTENTION: OEM quality. These are NOT original parts of the engine manufacturer!  Product details
Recommended retail price: €19.88
only  €18.95
-5%
You save: €0.93
> 100 | in stock
pcs.
Having issues?
If you are not redirected to PayPal, it could be due to your browser settings. Please check and if necessary deactivate the setting "Hide IP address" in the settings -> Safari -> Hide IP address. Please also check your browser for updates.
MyBoat
Are you already using this item?
Add to my boat now.

Available variants

MC97-Impeller for Volvo Penta/Lombardini/ Perkins/Ruggerini/Farymann/ Fischer
JOHNSON PUMP MC97-Impeller for Volvo Penta/Lombardini/ Perkins/Ruggerini/Farymann/ Fischer
€27.60
only €25.95
To product

Product data

  • SVB item number 27251
  • Description D1-Serie, D2-40, MD 2010-2040, MD3B, MD17C & AQ-Serie
  • Number of blades 6 Blades
  • Inner-Ø 13 mm
  • Outer-Ø 51 mm
  • Width 22 mm
  • Material Neoprene
  • For Volvo Penta AQ115, AQ130, AQ165, AQ170, D1-13, D1-20, D1-30, D2-40, MD3, MD17, MD2010, MD2020, MD2030, MD2040
  • Volvo Penta-No. 22222936, 3593659
  • Spare part for Inboard engines

SVB recommends

Image of Impeller Puller
-15%
SEATEC Impeller Puller
only €14.95

Product details

Note:

This product is delivered in original equipment manufacturer (OEM) quality. It is not the original product from the manufacturer.

An engine must be maintained regularly so that it can work optimally. This includes a regular impeller change. Only then can you keep wear low and extend the life of the engine. Gasket included. ATTENTION: OEM quality. These are NOT original parts of the engine manufacturer!

Our impellers are "OEM quality" approved and meet the requirements of engine manufacturers. Impellers are available for various engines. If your engine is not listed, please contact us. We will make sure we get the right impeller for you.

Volvo Penta
  • D1-13 A/B/F, D1-20 A/B/F, D1-30 A/B/F
  • D2-40 A/B/F
  • MD-2010/2020/2030/2040, MD3 B, MD17 C
  • AQ-115, AQ130 A/B/C/D, AQ-165 A, AQ170

Product safety

What other SVB customers have to say

100% real reviews

180 customer reviews

4.5 (out of 180 ratings)
  • Advantages
  • Accuracy of fit (6)
  • Quality (6)
  • Material (7)
  • Delivery contents (8)
  • Price/performance ratio (7)
  • Lifespan (5)
  • Disadvantages
  • Accuracy of fit (3)
  • Quality (1)
  • Price/performance ratio (1)
Torsten P.
by Torsten P. Flag of Germany 10/26/2015 Verified purchase Variant: 46300
I bought the impeller for a Johnson pump. At first glance everything is perfect, but after installing it I noticed that no water was being pumped. After a long puzzling over, I realized that the \ "wings \" are about 1mm shorter than the original. After installing the old impeller -> everything is okay
Enzo M.
by Enzo M. Flag of Italy 5/25/2015 Verified purchase Variant: 64310
PRODUCT UNDER EXPECTATIONS WITH INADEQUATE FINISH
Winfried W.
by Winfried W. Flag of Germany 9/1/2014 Verified purchase Variant: 46301
the tel. Advice was good, the effort of your employee to determine the right spare part, commendable. \ R \ nThe service life of the impeller with just a few hours of operation seems to me to be too short, the price too high. The use of the pump as a diesel feed pump may also not be optimal.
Daniel G.
by Daniel G. Flag of Spain 7/13/2025 Verified purchase Variant: 27251
It doesn't work on my MD2030D
Although the item description says it's compatible with the Volvo Penta MD2030, this isn't true in my case. The center stud is too wide and barely fits into the pump shaft groove. If you force it a little, it ends up stuck halfway in and is very difficult to remove.
  • Advantages
  • Material
  • Quality
  • Disadvantages
  • Accuracy of fit
Th. v. L.
by Th. v. L. Flag of Netherlands 4/15/2025 Verified purchase Variant: 27251
Poor quality, doesn't fit into the pump.
The part was poorly machined. It won't fit into the pump. The drive pin is not centered, so it's poorly machined and the quality control is poor.
  • Disadvantages
  • Quality
  • Accuracy of fit

Rate product

How would you rate this product?
Disappointed
Completely fails to meet my expectations
Poor
Only some expectations are met
OK
Meets my basic expectations
Good
Slightly better than my general expectations
Excellent
Fully exceeds my expectations
Click on the stars to rate

Customers ask customers

Technical question
Martin P. | Jul 2, 2021 Flag of English
User image of Martin P.

Is it good for water pump vetus st134?

Answer from SVB customer service
Cory V. | Oct 6, 2022
User image of Cory V.

Dear customer, please email [email protected] for technical support in this case.

Technical question
Martin P. | Jul 2, 2021 Flag of English
User image of Martin P.

Is it good for vetus water pump st134? Dimensions are similar. I need 12,17 mm 50,8 mm 22,1 mm 6 7

Answer from SVB customer service
Cory V. | Oct 6, 2022
User image of Cory V.

Dear customer, please email [email protected] for technical support in this case.

Technical question
David C. | Feb 15, 2021 Flag of English
User image of David C.

Is this the good impeller for a Volvo D3-110i please?

Answer from SVB customer service
Cory V. | Oct 6, 2022
User image of Cory V.

Dear customer, please email [email protected] for technical support in this case.

Technical question
Kenneth A. | Aug 2, 2020 Flag of English
User image of Kenneth A.

Looking for a new Impella for my Volvo Penta MS 2B engine. It looks lige your item no: 15698 is the right one. Can you confirm? Regards, Kenneth

Answer from SVB customer service
Cory V. | Aug 3, 2020
User image of Cory V.

Dear customer, yes it is the correct one. Thank you.

E-mail Newsletter

Product news, offers & new guide videos. Stay up to date!

WhatsApp

New: Get news from SVB straight to your phone!

Impeller for Volvo Penta D1 Series, D2-40, MD2010-2040, MD1 / 2 / 3B, MD11 / 17 & AQ Series
View Ratings (180) Questions (15)