QUICK QNC CHC Control Panel and Chain Counter

New generation It came as a replacement for the old model which broke down.

by Pompee L.

Extremely helpful gadget for providing chain length when anchoring and chain slacking We have three operating locations for the winch when anchoring. For lowering, we use the quick display during anchoring maneuvers from the cockpit - this is extremely convenient and the desired chain length can be determined in advance based on the water depth. Lower the anchor, directly from the rudder and read the chain depth. e.g. 2x water depth and 1x boat length. We don't use value settings as a given value... down with it and propeller backwards. Our anchoring maneuver is now 99% complete with just this measure. When catching up, we usually start from the cockpit and often catch up the last free meters directly using the sight control on the windlass. Very useful tool.... Gives you the right feeling of not using too much or little chain, especially between other boats. What I would like... To slow down the motor running of the anchor winch so much when catching up that you don't always have to start and stop the winch... I would like it to run continuously... Up and Down - Perhaps. an idea for later...

by Oliver V.

Good product I have the previous model in another boat. If you anchor often makes you life much easier.

by Georgios M.

Remote control... ...which is simply fantastic, but the watertightness of the previous model is unfortunately not great, so I had to replace the device; now I'm hoping that this one is watertight.

by Klaus P.

Product data

SVB item number 61249
EAN 8057090253962
Manufacturer no. FNQNCCHCF000B00
Description QUICK - QNC CHC control panel and chain counter
Remote control type Control panel
Operating voltage 12 V, 24 V
Number of outputs 1
Number of poles 5
with display Yes
Chain counter Yes
Integ. torch No
Wireless No
Cable length 500 mm
IP protection class IP67
Length 115 mm
Width 115 mm
Accessories for Windlasses
Installation depth 21.5 mm

SVB recommends

-23%

SEATEC Automotive/ATO Blade Fuse / Single

only €1.00

-20%

SEATEC ATO In-line Fuse Holder

only €3.95

-22%

SEATEC Toggle Switch ON-OFF

only €6.95

Accessories

Flexible Cables

from €0.95

13 Versions

WAGO Splicing Connector / 0.2-4.0 mm²

only €0.90

Product details

QNC CHC chain counter control panel from Quick for operating your windlass remotely. An integrated chain counter provides reliable information on the amount of chain lowered. The control panel also comes with a range of other useful functions, such as an automatic lowering function, alarm function and a function for weighing anchor. Data can be clearly viewed on the state-of-the art, 3.5" colour graphic display. Included in delivery: Display, gasket, screws for fastening, display protective cover, chain counter sensor kit, M12 power/control signal cable (0.5 m)

Further features at a glance

Extremely flat (only 6.2 mm mounting height)
Multilingual user interface
Display the lowered chain length in metres or feet
Windlass management with auto free fall
CAN bus communication interface for data transfer

Technical data

Display size	3.5"
Dimensions LxWxH total / H on console	115 x 115 x 32 / 6.2 mm
Dimensions of the protective cover LxWxH	120 x120 x 9 mm
System voltage	12 / 24 V DC
Power consumption with backlight on at maximum level	160 mA
Required fuse protection / maximum current capacity	4 A
External connections	Female M12 for POWER & I/O Male M12 for CAN bus
Material	Glass front
Protection	IP67
Colour	Black

Installation instructions

QUICK instructs to install a 4A fast-blow fuse.
It is possible to control one windlass with several chain counter instruments. To do this, a simple CAN-BUS network must be set up, via which the control units are connected to each other. For the network, pre-assembled data cables, connectors and terminators are used, which are all fitted with standardised M12 plugs/couplings.
M12 connectors are identical to NMEA2000 Micro-C or PHILIPPI PBus components. The material for setting up the network and connecting the devices can be found in our extensive range of NMEA2000 accessories and equipment.
To network 2 control units, you will need the following NMEA2000 components: 1x dual distributor (or 2x Ts), 2x or 3x network cable (you only need the third cable if you are working with Ts), 1x male terminating resistor, 1x female terminating resistor.

Operating voltage

12 V 24 V

Number of outputs

with display

Chain counter

61249_QUICK_Kettenzählwerk_QNC_CHC_Maße.jpg

Documents

Manual

PDF (3,30 MB)

Manual

PDF (4,46 MB)

Product safety

What other SVB customers have to say

100% real reviews

6 customer reviews

4.7 (out of 6 ratings)

5 Stars

(5)

4 Stars

(0)

3 Stars

(1)

2 Stars

(0)

1 Stars

(0)

100% recommend SVB

Advantages
Price/performance ratio (1)
Quality (1)
Mounting/Installation (1)

Disadvantages
Max. range (1)
Price/performance ratio (1)
Quality (1)
Mounting/Installation (2)

by Klaus P.

7/8/2025 Verified purchase

Remote control...

...which is simply fantastic, but the watertightness of the previous model is unfortunately not great, so I had to replace the device; now I'm hoping that this one is watertight.

Advantages
Price/performance ratio
Quality
Mounting/Installation

by Georgios M.

10/29/2024 Verified purchase

Good product

I have the previous model in another boat. If you anchor often makes you life much easier.

Disadvantages
Max. range
Price/performance ratio
Quality
Mounting/Installation

by Oliver V.

11/19/2023

Extremely helpful gadget for providing chain length when anchoring and chain slacking

We have three operating locations for the winch when anchoring. For lowering, we use the quick display during anchoring maneuvers from the cockpit - this is extremely convenient and the desired chain length can be determined in advance based on the water depth. Lower the anchor, directly from the rudder and read the chain depth. e.g. 2x water depth and 1x boat length. We don't use value settings as a given value... down with it and propeller backwards. Our anchoring maneuver is now 99% complete with just this measure. When catching up, we usually start from the cockpit and often catch up the last free meters directly using the sight control on the windlass. Very useful tool.... Gives you the right feeling of not using too much or little chain, especially between other boats. What I would like... To slow down the motor running of the anchor winch so much when catching up that you don't always have to start and stop the winch... I would like it to run continuously... Up and Down - Perhaps. an idea for later...

by Pompee L.

8/6/2023 Verified purchase

New generation

It came as a replacement for the old model which broke down.

by Christian V.

8/28/2022 Verified purchase