SUPERGAIN NOMADE DVB-T Antenna

The omnidirectional SUPERGAIN* NOMADE DVB-T antenna is suitable for boats and vehicles of all kinds, thanks to its compact design and low weight. An integrated amplifier provides a gain of 24.5 dB. The adjustable antenna base can be screwed or glued and therefore can also be used as a cable duct under deck or in a vehicle's interior. For uneven surfaces, an inclination compensation of +/- 15° is possible.
The amplifier is located in the antenna's housing and is supplied by a 12-volt supply voltage via a 5 m coax cable. The compact dimensions and flat design of the NOMADE make the antenna very streamlined, while also allowing it to be used as an indoor antenna.
Suitable for receiving terrestrially broadcast DVB-T1 / 2, TNT and HDTV signals.
Scope of delivery: Antenna with adjustable base and 5 m coax cable, V9114PI feed-through switch including a 250mA fuse, 1.5m TV connection cable and mounting screws.

Antenna

• Dimensions: Antenna with base: Ø 245 mm x 80 mm height
• Weight: 200 g (7 oz)
• Material: Acrylester-styrene-acrylonitrile (ASA)

Electrical properties

• Receiving angle: Omnidirectional, 360°
• Polarization: Horizontal
• Frequency range 170/890 MHz
• Average noise: 24.5 dB
• Noise factor: 1.7 dB
• Impedance: 75 Ohm
• Operating voltage: 12 V power supply
• Current consumption: Approx. 25 mA

Antenna connection cable

• Coax cable 3C-2V, 75 Ohm, white, 5 mm Ø, length 5 m
• Ready for connection with F connector
• Max. Ø F connector: 13 mm

TV connection cable

• Coax cable 3C-2V, 75 Ohm, white, 5 mm Ø, length 1.5 m
• Ready for connection with F- and TV- (IEC-male) connectors
• Max. plug-Ø: F connector 13 mm / IEC connector 15 mm

Inlet switch

• Dimensions (L x W x H): approx. 70 x 45 x 17 mm
• F socket ANTENNA IN
• F socket TV OUT
• 12 V DC - two individual wires, length approx. 25 cm (RED = POS12 V (including fuse), BLACK = NEG)
• Grounding clamp on housing (max. cable cross section: 10 mm²)
• Fuse: 250 mA, 5 x 20 mm
• Mounting option: a 4 mm hole

Delivery contents

• Antenna with foot and 5 m coax cable
• Inlet switch
• TV connection cable: 1.5 m
• 4x countersunk head screws: 3.5 x 16 mm
• 4x countersunk head screws: 2.9 x 9.5 mm

Mounting instructions

• The antenna base can be glued and / or screwed in place.
• The 5 m coax cable runs through the antenna base.
• If required, the TV connection cable can be extended by standard TV antenna cables (IEC / IEC connector).
• If required, the 5 m coaxial cable can be extended. Low-loss coax cables, F connectors and plugs can be found under accessories.

Electrical connection

• First connect the 5 m long antenna cable with the inlet switch, ANTENNA IN socket.
• Next, connect the 1.5 m long TV connection cable to the inlet switch, TV OUT jack.
• Connect the inlet switch to a 12 volt power source after connecting the coax cables.
• The inlet switch has a housing terminal. This can be connected to the vehicle's body.
• Be sure to follow the assembly sequence and avoid reverse polarity!
• Failure to observe this can result in short circuiting, and in the worst case, total failure of the inlet switch.
• Do not loosen / twist the screw connection of the DC voltage input!
• The cables could break off of the circuit board, which can lead to irreparable damage.
• Do not remove the plugs from the coaxial cables!
• Failure to observe the above points will result in the loss of your warranty.

* GLOMEX, Italian producer of high-quality and technologically-advanced marine / automotive antennas, offers antennas under the name SUPERGAIN with new and extraordinary designs at very good price to performance ratios.