INTERNATIONAL DANBOLINE Bilge Paint
SVB item number: 40889
Manufacturer no.: YMA102/750AR
Protects your bilges, lockers and bulkheads! DANBOLINE is resistant to residues of oil and fuel. Available in white and grey.
Product details
Having issues?
If you are not redirected to PayPal, it could be due to your browser settings. Please check and if necessary deactivate the setting "Hide IP address" in the settings -> Safari -> Hide IP address. Please also check your browser for updates.
If you are not redirected to PayPal, it could be due to your browser settings. Please check and if necessary deactivate the setting "Hide IP address" in the settings -> Safari -> Hide IP address. Please also check your browser for updates.
Are you already using this item?
Add to my boat now.
Product data
- SVB item number 40889
- EAN 5035686892019
- Manufacturer no. YMA102/750AR
- Description INTERNATIONAL - Bilge paint DANBOLINE
- Colour White
- Colour code white / YMA102
- Contents 0.75 l
- Yield (theoretical) 9.23 m²
- Finish High gloss
- No. of components 1 component
- Method of application Roller, Brush
- No. of coats (recommended) 1 - 2
- For substrate GRP, Wood, Steel, Aluminium
- Shipping information Dangerous goods
Product details
DANBOLINE from International protects your bilges, lockers and bulkheads. The paint is resistant to residues of oil and fuel. Available in white and grey. Yield: 12.3 m²/litre Thinner no. 1.
Processing instructions:
For coated surfaces:
All surfaces: Sand primer with 180-220 grit. Remove dust and then apply 1-2 coats of Danboline.
Bare wood: Prime the surface with ONE UP or Interprotect.
Aluminium: Prime the surface with ONE UP or Interprotect.
Steel: Prime the surface with ONE UP or Interprotect.
GRP: Clean the surface with Super Cleaner. and rinse afterwards. Sand thoroughly with 180-220 grit sandpaper. Clean well and allow to dry. No primer required.
Drying time at 15 °C: 8 hours
Processing time at 15 °C: min. 24 hours
Processing temperature: +15 °C to max. 35 °C
For coated surfaces:
- In good condition: Wash down with a suitable detergent, rinse with fresh water and allow to dry. Abrade with 180280 grade (grit) paper.
- In poor condition: Remove all previous coatings and prime the surface.
All surfaces: Sand primer with 180-220 grit. Remove dust and then apply 1-2 coats of Danboline.
Bare wood: Prime the surface with ONE UP or Interprotect.
Aluminium: Prime the surface with ONE UP or Interprotect.
Steel: Prime the surface with ONE UP or Interprotect.
GRP: Clean the surface with Super Cleaner. and rinse afterwards. Sand thoroughly with 180-220 grit sandpaper. Clean well and allow to dry. No primer required.
Drying time at 15 °C: 8 hours
Processing time at 15 °C: min. 24 hours
Processing temperature: +15 °C to max. 35 °C
Documents
Datasheet
PDF (192,05 KB)
Manual
PDF (2,07 MB)
Datasheet
PDF (198,19 KB)
Manual
PDF (2,54 MB)
Safety datasheet
PDF (210,00 KB)
Item 40890, 40891
Safety datasheet
PDF (214,25 KB)
Item 40889, 40999
Datasheet
PDF (192,48 KB)
Manual
PDF (1,94 MB)
Manual
PDF (1,96 MB)
Manual
PDF (2,03 MB)
Manual
PDF (2,21 MB)
Product safety
Please note the following hazard warnings:
UN number
UN 1263
Transport class
3
LQ weight
1 l
VOC content
411 g/l
Hazard pictograms
Signal word
Warning
Hazard warnings
Read label before use.
Keep out of reach of children.
If medical advice is needed, have product container or label at hand.
Wear protective gloves/protective clothing/eye protection/face protection.
Keep away from heat/sparks/open flames/hot surfaces. – No smoking.
IF ON SKIN (or hair):
Remove/Take off immediately all contaminated clothing.
Wash skin with water (or shower).
Keep cool.
Dispose of contents/container to …
Flammable liquid and vapour.
May cause drowsiness or dizziness.
Keep out of reach of children.
If medical advice is needed, have product container or label at hand.
Wear protective gloves/protective clothing/eye protection/face protection.
Keep away from heat/sparks/open flames/hot surfaces. – No smoking.
IF ON SKIN (or hair):
Remove/Take off immediately all contaminated clothing.
Wash skin with water (or shower).
Keep cool.
Dispose of contents/container to …
Flammable liquid and vapour.
May cause drowsiness or dizziness.
P103, P102, P101, P280, P210, P303, P361, P353, P235, P501, H226, H336
by
Philippe S.
5/6/2024
Verified purchase
5/6/2024
Verified purchase
Customers ask customers
Technical question
António B.
| Jun 24, 2021
I would like to know if must use a primer before, like the PRE-KOTE Undercoat on a paint of an old grp boat, i will paint the bilges and under decks. Also like to know if must be thinned with thiner on aply of two coats or apply directly without thiner. It will be apply with brush and roller.
Answer from SVB customer service
Cory V.
| Oct 12, 2022
Dear customer, please contact us at [email protected] in this case.
E-mail Newsletter
Product news, offers & new guide videos. Stay up to date!
WhatsApp
New: Get news from SVB straight to your phone!